#3Welcome to the PSDI VAX11/780
#4Welcome to the PSDI VAX11/780
#3Coming Attractions
#4Coming Attractions
#6Monthly Backups
Backup will start at 5:30pm Sharp.
Wednesday August 24
Monthly backup of the 780 and the 730's.
Thursday  August 25
Monthly Backup of the 750 and the 780's RP07.
The 780's PROJECT/2 Disk will be off-line from 7am to 8am on
Wednesday Morning August 24

Username: ROBIN/NOCOM
Password: 
        Welcome to VAX/VMS version V3.2 on node TERRA
$ !
$ ! If no wait string is specified, we simply loop reading characters until
$ ! we become idle.  The definition of idle is when we presume the remote
$ ! isn't sending us any further data.  We presume we are idle when our
$ ! remote read times out after 'n' seconds (1 by default).  The symbol
$ ! SCRIPT_TMO can be defined to override this timeout.
$ !
$ ! The remote read routine (READ_DATA) uses timeout count of 1 for the
$ ! number of seconds allowed between receiving each character.  This can
$ ! be overridden with the symbol IDLE_TMO.  If running in batch, you may
$ ! want to increase this count to 2.
$ !
$ ! Since many commands such as a "DIRECTORY" will have 2 seconds delays
$ ! due to system load, you can specify a wait string.  In this command file,
$ ! the wait string is defined as "^M$" which is the prompt used by VMS.
$ ! The script loops up to 'n' times (5 by default) looking for this string.
$ ! The symbol WAIT_TRYS can be defined to override this default.
$ !
$ ! If the command line starts with an up arrow (^), all characters on the
$ ! line with the ^char format are converted to control characters. This
$ ! command file uses an "^Z" to terminate the CREATE command.
$ !
$ create test.dat
1
2
3
4
5
6
7
8
9
10
^Z
$ !
$ ! The format of the .WAIT command is ".W[ait] string".  Characters of the
$ ! form ^char are converted to control characters.  The string may contain
$ ! contain embedded spaces but can not start with spaces.
$ !
$ SHOW TERMINAL
Terminal: _TTA1:          Device_Type: Unknown       Owner: _TTA1:(ROBIN)

   Input:   1200      LFfill:  0      Width:  80      Parity: None
   Output:  1200      CRfill:  0      Page:   24

Terminal Characteristics:
   Interactive       Echo              Type_ahead        No Escape
   No Hostsync       TTsync            Lowercase         No Tab
   Wrap              Scope             Remote            No Holdscreen
   No Eightbit       Broadcast         No Readsync       No Form
   Fulldup           Modem             No Local_echo     Autobaud
   No Hangup         No Brdcstmbx      No DMA            No Altypeahd
   Set_speed         No ANSI_CRT       No Regis          No Block_mode
   No Advanced_video No Edit_mode      No DEC_CRT
$ !
$ ! Use the .W[ait] with no wait string to prevent script from looking for
$ ! a wait string.  This is used when you want to send one line after another
$ ! as in the CREATE command used in this command file.  The wait string can
$ ! then be reenabled when you expect a prompt string.
$ !
$ create test1.dat
The .WAIT must be in uppercase to be found, otherwise the command is
sent to the remote system.
.wait string
.11
.12
.13
.14
.15
^Z
$ TYPE TEST.DAT,TEST1.DAT
1
2
3
4
5
6
7
8
9
10
The .WAIT must be in uppercase to be found, otherwise the command is
sent to the remote system.
.wait string
.11
.12
.13
.14
.15
$ DELETE *.DAT;*/LO
%DELETE-I-DELETED, USER2:[ROBIN]TEST.DAT;2 deleted
%DELETE-I-DELETED, USER2:[ROBIN]TEST.DAT;1 deleted
%DELETE-I-DELETED, USER2:[ROBIN]TEST1.DAT;1 deleted
$ DIRECTORY

Directory USER2:[ROBIN]

ANON.DIR;1          BASIC.COM;1         BASIC.DIR;1         BASIC.HLB;2
BATCH.LOG;1         BLISS.DIR;1         BRU.COM;1           CAT.DIR;1
CCP.DIR;1           CLOCK.COM;1         CLOCK.TXT;1         CMD.DIR;1
COM.DIR;1           CONFIG.DIR;1        COPY.MEM;1          COPYRIGHT.MAC;1
CVT.DIR;1           D.JOU;1             DAMMIT.DIR;1        DDT.DIR;1
DECUS.CMD;2         DECUS.CMD;1         DECUS.COM;1         DECUS.LST;3
DIR.DIR;1           EDTINI.EDT;8        EDTKEYS.TXT;4       END.JCL;1
ESTPIESQ.QWK;1      EXE.DIR;1           F4P.JCL;1           FAL.LOG;1
FINGER.PLN;1        FLOPPY.DIR;1        HELP.COM;2          ICE.DIR;1
ICR.DIR;1           JUNK.DIR;1          LBRSHR.EXE;2        LIST.COM;1
LIST.DIR;1          LOGIN.COM;1         M.MAI;1             MAIL.MAI;1
MAR.DIR;1           MASH.DIR;1          MDL.DIR;1           MEMO.DIR;1
MISH.DIR;1          P2.DIR;1            PHONE.DIR;1         PLOT.DIR;1
PNG.DIR;1           PRIV.COM;1          Q.COM;1             R.COM;1
R.MAI;1             RIXON.LOG;1         RNO.DIR;1           ROBIN.MSH;1
RSXV4.DIR;1         SCRATCH.DIR;1       SD.LOG;3            SHOW.DIR;1
SIGNON.JCL;1        SLAUGHTER.EXE;1     SYS11.DIR;1         T.JOB;3
T.JOB;2             TAB.DIR;1           TBL.TXT;1           TEC.DIR;1
TOM.LST;1           TPARS.DIR;1         TRNTBL.TXT;1        UNIX.DIR;1
USERS.DIR;1         VAXNET.DIR;1        VAXNET.NEW;2        VCOM.DIR;1
VTL.DIR;1           VTM.DIR;1           WHO.DIR;1           ZBDRV.DIR;1
ZG.DIR;1            

Total of 85 files.
$ LOGOUT
  ROBIN        logged out at 26-AUG-1983 14:24:37.53